UV Aging Test Chamber common to 3 points of failure cause analysis

UV Aging Test Chamber common to 3 points of failure cause analysis

Problem 1. UV lamps do not light up or flicker.
 
Cause.
UV lamps in use, sometimes the lamp does not light up, sometimes the light or flicker. This is because the UV Aging Test Chamber is generally used are electronic ballasts, electronic ballasts are wired for the jack type. So some times because of the details of the production process is not very good, it is easy to lead to the lamp corner line in the connection with the electronic ballast there is a hidden danger of insecurity, in the future use of the process will appear gap off line, poor contact and other problems. Or because the lamp voltage is too high and the transformer does not match, please measure the lamp power and related parameters.
UV Aging Test Chamber
 
Problem 2. The UV lamp is black at both ends.
 
Cause.
This is because the head of the UV lamp is tungsten, its melting point is 3410℃, when we light the lamp, the temperature is between 2000 and 3000℃, the filament will not melt, sublimation will occur, then the sublimated tungsten vapor meets the wall of the tube and condenses into solid tungsten, making it black, and the filament of the UV lamp is at the two ends of the lamp, so the two ends will become black. When the UV lamp starts to turn black, it needs to be replaced. So in order to extend the life of the lamp, please do not start and shut down the lamp frequently. According to the standard, the lamp should not be turned off for less than 3 hours since the lamp is lit.

评论

发表评论

此博客中的热门博文

The secret of stable UV Accelerated Weathering Tester operation

图片
The secret of stable UV Accelerated Weathering Tester operation 1, the specification of  UV Accelerated Weathering Tester  placement site and location: in the installation of equipment in the site is not just the size of the site, in addition to the temperature, humidity and other conditions must be met, the site can not store flammable and explosive and fire-prone hazardous materials, when the site to meet the requirements, the installation location of the equipment also has requirements, as the equipment in operation will be Generate heat dissipation, so you can not stack items around the equipment, so as not to affect the test results, in addition to the site around the emergency treatment facilities such as fire extinguishing, in order to avoid unwanted accidents lead to serious consequences. 2, try to avoid improper operation: such as improper operation, the light may lead to inaccurate results, due to excessive weight may lead to failure, etc., so the operator should mas...
阅读全文

How to eliminate the safety hazards of xenon lamp test chamber?

图片
How to eliminate the safety hazards of xenon lamp test chamber? How to eliminate the xenon lamp test chamber safety hazards? xenon lamp test chamber has the following safety protection systems. 1. refrigeration system: leak detection test, compressor overheating, compressor overpressure; 2. Humidification system: heating tube dry burn, abnormal water supply, water shortage alarm; 3. Circuit system: over temperature protection, fan motor overheating, overall equipment under phase / reverse phase, overall equipment timing, leakage protection, overload and short circuit protection. When installing the xenon lamp test chamber, pay attention to the following points to ensure personal safety: 1. Power supply: The power supply of the equipment uses a three-phase five-wire system, and the equipment cable is four-core wire, three phase wires, and one neutral wire. Please pay attention to the distinction between neutral wires. Because part of the load and control system of the equipment is singl...
阅读全文

Tips for choosing an Ozone ageing chamber

图片
Tips for choosing an Ozone ageing chamber : The choice of environmental temperature: some products need to be tested in a temperature environment of minus degrees Celsius ozone resistance test, some are tested at room temperature, and some are tested at high temperatures. Users just need to understand their own products to test the common test temperature can be. It is important to note that testing at room temperature is more common. Conditions can be placed in the Ozone aging chamber premises equipped with air conditioning systems, it is recommended that users choose the test chamber with a refrigeration system when purchasing, to avoid the summer test, the temperature is too high resulting in inaccurate results. Chamber volume selection: because the Ozone aging chamber chamber materials and ozone concentration control accuracy difficulties will have a corresponding increase, so as long as the test products can be accommodated on, too large chamber will only cause waste.
阅读全文